Plumbing & HVAC Company near Prosper TX
Chrome Heating, Air & Plumbing provides local air conditioning repair, heating system and plumbing services to residents in Prosper, TX and the surrounding areas. Need to replace your HVAC system or equipment? Is your hot water heater running as efficiently as it should? Contact Chrome for highly recommended HVAC repair and plumbing services today!
Local Heating & Air Conditioning Contractor & Plumbing Company
Read our reviews below to find out why your neighbors consider us to be their go-to AC contractor and plumber expert in Prosper, TX.
Good communication. On time. I signed up for yearly maintenance. Jeremy our tech was professional and informative
Jeremy was awesome. Great service tech
Good job. Polite fast.
Performed a two system maintenance checking heating. Starting with the inside air handlers, checked blower amps, heat strip amps and checked filter. Found both filters needing to be changed out. Found that the downstairs unit has a blower motor ecm going bad causing the motor to spudder when starting up and stay like that. Was able to reset the breaker a few times and get it unstuck. Motor may fail again in future. Checked outdoor units amp draws and pressures. Checked reversing valve. Found that the downstairs unit is also a few pounds low on Freon. System is out of warranty. Recommended a leak search for downstairs unit. Sent estimate over for repairs.
Upon arrival found system giving a error code 2 +3 which is for low pressure switch failed open. Checked flu pipe it was clear, checked exhaust and intake at rain cap and they were clear. This time the furnace would not lite the burners after resetting it. Called tech support and he had me check to see if board would lose 24v signal from pressure switches and it didn’t. Tech support said that since it never lost signal the control board is bad. Told tech support that previous company tried replacing board and it didn’t work. Previous company also had pressure tubes reversed when new board was installed. Board ordered at Lennox in Allen.
Order#33781055
Upon arrival found that system 48 isn’t working again. Turned system on and checked condenser. Found that I didn’t have me fitting to connect gauges, went to get fitting and returned. Found pressures were low. With approval performed a leak search. Checked all the valves, Lines and fittings I could get to and could find leak. Spoke with Steve and he said that the indoor unit can’t be taken off of wall to get to lines. Steve wanted to put Freon back in it and get it going for now until they cut open wall and try to isolate leak. With approval pulled vacuum on system and charge system a little under 3lbs. System holds 40.6oz. Turned system on and system is now working properly for now.
Upon arrival found downstairs system not heating. Turned system on and checked furnace in attic. Found that system was giving a low pressure switch fault. Found that the positive and negative pressure switch tubes were switched. Swapped tubes and tried to turn on system again. System did not come on. Tried to check wiring for pressure switched but couldn’t find a good enough diagram. Called tech support and they had me wire the switches correctly. Checked igniter and drain tubes for furnace all were clear. Turned system on and furnace came on. Cycled unit three times and tested second stage system is heating properly at this time.
Performed a one system maintenance checking heating and plumbing inspection. Checked all electrical, mechanical and safety components, checked amp draws and sequence of operation. Checked filter and pressure. Found that there is some growth in the inside unit that need to be cleaned out, found contactor pitted from short cycling. Found outdoor coil and filter dirty. Found that the exterior txv is stuck closed and will need to be replace to work properly. Emailed estimate over to repair or replace. System didn’t get registered so it’s out of warranty. Highly recommend replacing system.
On plumbing checked all stops, toilets, sinks, drains, showers, water heater. Everything checked out good. Left side sink in master and half bath sink are draining a little slower than others.
Performed a two system maintenance checking heating. Checked all electrical, mechanical and safety components. Checked set up of unit and sequence of operation. Both systems are operating properly at this time. I did have to set up downstairs unit for 2nd stage heating. Also on next visit homeowner would like quote on adding another mini split to other garage.
Everything was solid.
Checked amp draws on inducer fan motor and blower motor, cleaned flame sensor checked air filter, checked safety devices, checked heat exchanger it was good, checked igniter, sequence of operation. Adjusted gas pressures on gas valves to proper range. Both systems are heating properly at this time.
Upon arrival installed new display for downstairs system and turned system on. System gave an e202 error for mismatch blower. Called tech support and found that the board wasn’t programmed for right blower motor. Set board and code disappeared. System is now operating properly at this time. Installed new display for upstairs unit and turned system on. System is working properly at this time. On master system removed thermostat and installed new s30. Checked set up and system is working properly at this time.
Checked amp draws on inducer fan motor and blower motor, cleaned flame sensor checked air filter, checked safety devices, checked heat exchanger it was good, check igniter
Upon arrival homeowner stated that another company came out and stated that the downstairs. Checked outdoor unit and found that the compressor was locked up. LRA was 92amps and it was rated for 67amps. Compressor is under warranty, compressor is back order and expected to arrival by the end of the month. Homeowner is ok with waiting for compressor.
Upon arrival found that the upstairs unit was not cooling. Turned system on and checked indoor unit. Checked filter and coil. Found coil to be rusted pretty bad on the bottom. Checked outside unit and found pressures low about 3-5lbs low. System is out of warranty. Made recommendations and homeowner would like to move forward with replacing coil. Will need to order coil.
Upon arrival found system not giving any current alerts. Checked alert history and didn’t find error code 425. Found error code 434 on oct 24. Where the control board lost communication with inverter board in outdoor unit. Checked com voltages going to inverter and was getting 4.9-5v dc. Error code 425 is saying that the compressor minimum speed is increased for better oil return due to low ambient temperatures. System is operating properly at this time. If error happens again to let us know.
Checked amp draws on inducer fan motor and blower motor, cleaned flame sensor checked air filter, checked safety devices, checked heat exchanger it was good, check igniter
Upon arrival found that all systems have the i30 thermostat, downstairs and upstairs units were the ones having issues. Homeowner had two s30’s and was able to install them. Once installed on the downstairs unit display would not light up, checked all voltages and they were good. Noticed that once I put the display on the dc voltage would drop out. Tried using upstairs display and same thing would happen. Called Lennox tech support and they said it was an internal short in the display and the display will need to be replaced, will warranty out display, also mentioned about replacing the master units Tstat since it’s an i30 as well and homeowner wants to move forward with warranting out displays and thermostat will need to return
Checked amp draws on inducer fan motor and blower motor, cleaned flame sensor checked air filter, checked safety devices, checked heat exchanger it was good, check igniter
Performed a one system maintenance checking heating. Checked inside units electrical and mechanical components, checked gas pressures, heat exchanger, blower and draft motor amps, filter, cleaned flame sensor, furnace is heating properly at this time. Recommended adding a uv alight/air scrubber to the system. Homeowner signed up for maintenance annually
Upon arrival customer had two units to look at. First one was DFCU48 which was a mini split. System has and E2 error code. Reset system and system came on. Went to roof top and mini split had low Freon levels. Customer wanted to recharge unit. Added 3lbs to system, mini split is now cooling. The other system covers the left front kitchen area. Found drain pan full with float switch activated. Found main drain line not backed up and dry. Dumped water that was in drain pan into main drain line and water drained properly. System came back on and watched water drain into main drain line properly. Checked to see if coil was level, checked to see if drain pan was cracked and both were good. Recommended sticking some treatment tablets in main drain pan.
Upon arrival found that unit 112 which covers right side conference room was not cooling. Checked inside unit and found that the drain line was clogged and the filter was dirty. Checked outdoor unit and found pressures a little low, spoke to Michael and wanted to add Freon and clear out the drain line. Added 3lbs of 410-A to system to set charge. Went to inside unit and cut drain line and blew out trap and line. Primped trap and watched system drain properly. System is now cooling at this time.
Upon arrival unit 119 had water in pan again. Checked to see if unit was leveled correctly and it was. Checked pan again for cracks none found. Checked to see if main drain port was clogged and it wasn’t. Cut drain open and blew out line with drain gun. Line felt cleared, blew out line five times and felt no back pressure in line. While drain was disconnected water was draining fine into cup. No water was coming out of secondary or sweating off of unit. Connected drain back together and water was draining fine. Told Michael we’ll see what happens.
Upon arrival found that the upstairs unit was not cooling, checked inside unit and found everything operational, checked filter is was good, checked outdoor unit and found it not running. Found that the systems capacitor had went out. System is a 2018 and is still in the 5 year warranty. Replaced capacitor and system came on, checked pressures and they were good. System is now cooling at this time.
Replace Moen shower cartridge in trhe Main Bathroom.
Upon arrival found main unit of home not cooling. Checked inside unit and found everything operational. Checked outside unit and found the system not running found that the system had tripped off of high pressure reset the pressure switch and noticed that my high side pressure was slowly rising up. Checked filter dryer and unit and temperature across dryer was even. System has a clogged TXV. Homeowner approved repair. Went to Lenix in Allen to get TXV. pump system down and removed and installed new TXV. Pulled vacuum down to 500 µm purged system with Freon and release charge back into system Freon levels look good. Replaced 40/5 MFD capacitor for unit checked amp draw‘s everything looks good. Checked temperature differential and system has a 74° return with a 52° supply. Tried to call homeowner to collect payment but was not able to get a hold of homeowner still need to collect payment.
Upon arrival found outdoor unit coming on but blower not. Checked inside unit and found that the control board was not sending 24v to blower motor to tell it to come on. Also found that the speed tap wire for heat and coil were together. Separated taps so system could operate properly. System is 4yrs old and still under warranty. Homeowner approved repairs, Due to Lennox being closed will need to order parts in the morning.
Upon arrival found system short cycling. Checked inside unit and found coil frozen up. Checked filter and found it dirty. Homeowner stated that they just changed out the filter Friday. Turned down run time for fresh air intake. Left Tstats on and shut off outdoor condenser. Will need to return once coil is thawed out to see if it’s a refrigerant issue or air flow.
Upon arrival had no answer at the door. Rang doorbell and knocked on the door, got no answer.
Upon arrival turned system on and checked pressures. Pressures looked good. Filter was the cause of system icing up. Recommended adding start assist to compressor to ease the start up since it is a zoned system and turns on more than a normal set up.
Local Reviews
for Prosper, TXOur Reviews by City
Great service
Marilyn - Prosper, TX
Great Service
Brent - Prosper, TX
Great Service
Elwin - Prosper, TX
Great service
Jeremy - Prosper, TX
AC repair
Don - Prosper, TX
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
dispatch@chromeairconditioning.com
Powered by Nearby Now